Roof sheet is generally used for cold rolled steel sheet, galvanized steel sheet, color steel sheet and other different types of thin steel sheet, the thickness is generally 0.15 to 1.2 mm, and then after rolling, cold bending, its section can be V-shaped, U-shaped, etc., the section can also be trapezoidal or similar waveform, profile roof sheet is also known as building profiled steel sheet or corrugated steel sheet for short. The quality of anti-corrosion coating directly affects the service life of roofing sheet because the original plate is very thin. In order to meet the requirements of processing and anti rust, the coated steel plate should be inspected according to relevant regulations. When roofing steel sheet is used as panel and wallboard of houses in industrial factories, the steel consumption per square meter is about 5-11kg under the condition of no insulation requirement. When insulation requirements are available, mineral wool boards, glass wool and foam plastics can be used as insulation materials. The composite floor made of metal roof tile and concrete can be used as load-bearing structure without wood formwork. At the same time, in order to strengthen the binding force between profiled steel plate and concrete, it is better to pre weld studs on steel plate or press two-way stiffeners. Color Roof Sheet,Galvanized Roof Sheet,Metal Roof Tile,Profiled Roof Sheet,Corrugated Steel Sheet Jinan Hengming Steel Co., Ltd , https://www.jnhengmingsteel.com
Technical Information for extruder machine single screw barrel
Main Base materials
1.38CrMoAlA (SACM645)
Main Alloy Materials
1. Ni-based alloy/Deloro alloy
2. SKD-61 (Special Tool Steel)
2. Tungsten carbide/Wolfram carbide
3. 42CrMo (Ultrahigh StrengthSteel)
3. NiCo-based alloy
4. DC53 (Cold WorkDie Steel)
4. Fe-based alloy
5. W6Mo5Cr4V2 (High-SpeedToolSteel)
5. Co-based alloy
Processing Technics
1. Heat treatment
Technical parameters
Nitriding layer depth:0.5-0.8mm
2. Quenching
Nitrided hardness:900-1000HV
3. Nitriding treatment
Bimetallic layer depth:3 mm
4. Bimetallic alloy welding for screw
Bimetallic hardness:57~69HRC
5. Bimetallic alloy centrifugal casting for barrel
Hard-chrome plating hardness after nitriding:≥950HV
6. Hard-chrome electroplating
Chrome-plating layer depth:0.03-0.09mm
Linearity of screw:0.015mm
Surface roughness:Ra 0.4
Screw types:
Gradual change, chop, barrier, distributary, separate, air exhausting, pin, mixing and etc.
For good plasticizing effect, we have different design of screw barrel to meet customer's demand.
Specification :
Dia 20mm-250mm; L/D=15-45
Scope of Application:
1. Generally plastic material
2. Pipe/ Profile/ Sheet/Pelletizing
3. WPC, ABS, TPR, TPU, PMMA, C-PVC, UPVC, RPVC, PET, EVA, PU,PE etc
Treatment:
Nitrized, Chrome coating, Quenching, Bimetallic
We are foucs on each process to make sure each screw barrel is qualified according to technical requirement. 
Packaging Details:
1. Be brushed anti-corrosive oil on extruder machine single screw.Â
2. Packed with film.Â
3. Packed in the AA wooden.
Please provide samples or requirements about dimensions and tolerances of , semi-finished and finished products, the equipment, the monthlly comsumption quantity, the current screw and barrel you are using, HRC and so on.
For more information, please kindly contact as below:
Mobile: 0086-13917356326
Technical Information for extruder machine single screw barrel
Main Base materials
1.38CrMoAlA (SACM645)
Main Alloy Materials
1. Ni-based alloy/Deloro alloy
2. SKD-61 (Special Tool Steel)
2. Tungsten carbide/Wolfram carbide
3. 42CrMo (Ultrahigh StrengthSteel)
3. NiCo-based alloy
4. DC53 (Cold WorkDie Steel)
4. Fe-based alloy
5. W6Mo5Cr4V2 (High-SpeedToolSteel)
5. Co-based alloy
Processing Technics
1. Heat treatment
Technical parameters
Nitriding layer depth:0.5-0.8mm
2. Quenching
Nitrided hardness:900-1000HV
3. Nitriding treatment
Bimetallic layer depth:3 mm
4. Bimetallic alloy welding for screw
Bimetallic hardness:57~69HRC
5. Bimetallic alloy centrifugal casting for barrel
Hard-chrome plating hardness after nitriding:≥950HV
6. Hard-chrome electroplating
Chrome-plating layer depth:0.03-0.09mm
Linearity of screw:0.015mm
Surface roughness:Ra 0.4
Screw types:
Gradual change, chop, barrier, distributary, separate, air exhausting, pin, mixing and etc.
For good plasticizing effect, we have different design of screw barrel to meet customer's demand.
Specification :
Dia 20mm-250mm; L/D=15-45
Scope of Application:
1. Generally plastic material
2. Pipe/ Profile/ Sheet/Pelletizing
3. WPC, ABS, TPR, TPU, PMMA, C-PVC, UPVC, RPVC, PET, EVA, PU,PE etc
Treatment:
Nitrized, Chrome coating, Quenching, Bimetallic
We are foucs on each process to make sure each screw barrel is qualified according to technical requirement.Â
Packaging Details:
1. Be brushed anti-corrosive oil on extruder machine single screw.Â
2. Packed with film.Â
3. Packed in the AA wooden.
Please provide samples or requirements about dimensions and tolerances of , semi-finished and finished products, the equipment, the monthlly comsumption quantity, the current screw and barrel you are using, HRC and so on.
For more information, please kindly contact as below:
Mobile: 0086-13917356326
Model NO.: GMT-Screw
Nitrided Depth: 0.5-0.8mm
Surface Roughness: <=Ra0.4
Trademark: GMT
Transport Package: AA Wooden Case
Specification: Customize
Origin: China
HS Code: 84779000
Model NO.: GMT-Screw
Nitrided Depth: 0.5-0.8mm
Surface Roughness: <=Ra0.4
Trademark: GMT
Transport Package: AA Wooden Case
Specification: Customize
Origin: China
HS Code: 84779000