1. First of all, slowly and steadily prevent the transport tanks of bulk feed carriers from being in the car, and then fix them firmly. Under careful inspection, all parts of the transport tank have no damage due to transportation, and there is no water or debris in the transport tank of the bulk feed truck under the inspection of the open top lid, if any. It should be cleaned in a timely manner. 2. Then, the three-phase socket configured by the manufacturer together is installed near the material tower. The details to be noted here are that a waterproof device needs to be installed. 3. Plug the power plug of the transport tank of the bulk feed carrier into the top of the socket, and then start the button of the hydraulic pump. After running for two minutes, open the lift handle 6. The order of the lift and the arrows indicate If it is consistent, then it is correct. Otherwise, it is necessary to adjust the line sequence of the power line, and it is consistent to adjust to the order of operation and the arrow indication is consistent. 4. When the lifting and lowering handle 6 is operated, the lifting conveyor 7 is raised to a position 15 cm to 10 cm above the feed inlet of the material tower, and the control handle 5 is rotated to rotate the lifting conveyor 7 to the mouth of the material tower. The corresponding good position, and then start lifting conveyor 7 button to open the vertical conveyor 8 button, and finally open the flat conveyor 9 began to feed the feed tower. 5. After the feeds are all finished, they should be closed first, closed again 8 and finally closed 7. Finally, the control handle 5 moves the lifting conveyor 7 back to the original position, and the control handle 6 falls on the lifting conveyor again. Above the bracket. 6. After the entire feeding process is completed, the bulk feed carrier can only move the tanker eight plugs. 7. If you think the conveyor's rotation speed is too happy, you can adjust the lower throttle valve to make it rotate evenly. note: 1, in the operation of the hydraulic pump handle can not be too hard, it should be uniform outward movement or pull inward. 2. When the lifting conveyor moves, it should be lifted upwards, and the rising angle cannot exceed 45 degrees. Then move it to the right and left. The angles of the two sides moving left and right should be 75 degrees each, and the whole The corner cannot exceed 135 degrees. 3, when the conveyor is restarted, it must be operated according to the requirements of the instruction manual, and it cannot be arbitrarily changed. (Text / Sun Ni)
Overview: Honing is to use the honing head honing workpiece and finishing on the surface of the grinding machine. It is mainly used in automobile, tractor, hydraulic parts,
bearing, aviation and other manufacturing industries to honing the workpiece
hole. Honing Machine has vertical and horizontal two kinds.
Our company main product Vertical Honing Machine(half automatic and CNC ) and Horizontal honing machine.
1.vertical honing machine spindle working travel shorter, suitable for honing cylinder body and casing hole, etc.With oil stone Mosaic honing head driven by the placement of the vertical spindle rotation, at the same time in hydraulic device driver operating vertical reciprocating feed movement.(see picture)
2.Horizontal honing machine work schedule long, suitable for deep hole honing, depth of up to 3000 mm.The placement of horizontal honing head not rotating, axial reciprocating motion, workpiece by the spindle drive rotation, for lathe bed in the middle of the workpiece at the center of the frame and the supporting honing rod guide frame.In the machining process, the honing head oil stone in swell-shrink institutions operating radial feed, the workpiece processing step by step to the required size.A new type of honing machine adopts hydraulic swell-shrink honing head.Most of honing machine is semi-automatic, often with automatic measuring device, can also be incorporated in the automatic production line of work.In addition to processing hole honing conversion, processing and other surface of the cylindrical honing machine, bearing raceway honing machine, flat honing machine and surface honing machine, etc.(see picture )
Operation requirements
1.Honing machine operation has a certain technology, need a understand technical person, this person should be trained about grinding safe operating methods.And make necessary preparation before operation can be carried out
2.Check the lubrication part of the honing machine, especially the gearbox, see if there were any lubricating oil.If there is no oil, to all the oil injection hole filling.
3.Check coolant cleaner.If insufficient cooling fluid, coolant will be listed.Coolant to regular cleaning, not allowed to use a squalid coolant.
Continuous work two months later, the need for an oil change.Under normal circumstances, in the first quarter in oil at a time.The hydraulic oil 20 # engine oil should be adopted in general.An oil change, need to use kerosene oil filter and oil tank cleaning.
4.After the machine is idle for a period of time, in order to discharge the air in the hydraulic line, and check the work of each part is normal.
Machine with hydraulic oil temperature, generally does not allow more than 60 ℃, the highest must not exceed 65 ℃, otherwise the cooling measures should be taken or stop working.
5.Check the sharpening stone size is correct, whether the honing head increases and flexible, fastening oilstone seat spring is strong.
6.Adjust spindle rotation and reciprocating motion, make it meet the requirements of the process specification.
7.Measuring tool ready, and check the door of the work is normal, the precision of measuring whether or not up to standard.
8.Need to check in accordance with the requirements in place to ensure the personal safety and honing machine work in place.
PICTURE:
1.Half automatic honing machine (Also named ordinary honing machine)
Technical services include:
1. Pre-sale consultation and necessary process test;
2. Cooperate with the user to select suitable models and offer;
3. The machine installation, commissioning, test processing and training operators;
4. Equipment warranty troubleshooting and maintenance;
5. Warranty period of all kinds of services, including troubleshooting and maintenance
Honing Machine Honing Machine,Hydraulic Honing Machine,Vertical Honing Machine,CNC Vertical Honing Machine NingXia DaHe Machine Tool (Group) Imp And Exp Co.,Ltd , https://www.nxdhjcmachine.com
